Systems & Services

Building Systems Optimization with AI

Optimal staging, sequencing, and setpoints change continuously with load, weather, and equipment condition. No fixed sequence written at commissioning can follow that. AI agents can — running your systems in real time, holding the same output at lower energy input, without trading away comfort.

The Distinction That Matters

Analytics Reports. An Agent Acts.

For a decade the industry’s answer to building performance has been analytics — fault detection, diagnostics, dashboards. It finds real problems: a stuck damper, a leaking valve, simultaneous heating and cooling. Then it hands you a list and waits.

What analytics does

It Recommends

The findings are usually correct. But every one of them becomes value only if someone has time to act on it — and the list lands on a team that was already short-handed before it arrived.

A finding nobody acts on saves nothing.

What an agent does

It Controls

An agent doesn’t ask. It operates the system, adjusting staging, sequencing, and setpoints continuously — within the constraints your BMS already enforces.

No work order, no queue, no waiting on labor you don’t have. The correction happens when the condition does.

Analytics is worth having. It just isn’t the same thing as having the work done.

The Agent Team

Available Now

Each agent deploys on its own or alongside the others.

● Available

Chiller Agent

Drives the cooling plant to its best achievable efficiency at every load condition, continuously.

● Available

Cooling Tower Agent

Steadies heat rejection so the plant isn’t fighting its own condenser water, and reduces the load it has to carry.

● Available

Portfolio RTU Agent

Manages comfort, airflow, and cost across hundreds of rooftop units at once — built for portfolios, not single sites.

● Available

AHU Agent

Adjusts air distribution and thermal conditions dynamically as what the building needs changes through the day.

Under Development

Boiler Agent

Intelligent orchestration of heating plant operation.

Hot Water Agent

Thermal distribution tuned to demand, without unnecessary cycling.

Refrigeration Agent

Precision control for food service and cold storage environments.

Air Source Agent

Balances outside air against conditioned air as conditions shift.

We bring each one forward only after we’ve seen it work.

Why We Chose This

We Picked It Because We Watched It Work

We didn’t select this technology because it was available. We selected it because we watched it perform on real plants, with metered results — and that’s what we’ll show you, not a brochure.

It runs on top of your existing controls rather than replacing them. No rip-and-replace, no new front end to learn, no disruption to the sequences your building already depends on.

And — consistent with everything else we do — no lock-in.

Because the agents work through open interfaces on an open system, the optimization layer is itself replaceable. If something better exists in three years, you swap the agent without touching the plant controls underneath. That’s a claim no proprietary stack can make about its own AI offering.

Our Technology Partner

HDC Automation deploys and supports Facil.ai agents. We handle the assessment, the integration, the commissioning, and the ongoing support — the same way we handle every system we put in a building. You work with us; the agents work with your plant.

Estimate Your Savings

What Could Your Plant Return?

Enter your chiller plant’s numbers below for an estimate of what optimization could return annually. The math is straightforward and we’ve shown our work. A real assessment uses your trend data, but this will tell you whether the conversation is worth having.

Combined nameplate capacity
Typical load, not peak
Plant-wide, including auxiliaries
Blended rate from your utility bill
Months the plant operates
Average daily runtime
Annual Run Hours
8,640
Current Annual Energy Cost
$567,486
Estimated Annual Savings
$86,445
Based on these numbers, this plant may fall below the threshold where optimization pays for itself. That’s worth knowing before you spend anything — and it’s worth a look at your actual load profile, since a short season with heavy peak load sometimes behaves differently than these averages suggest.

Savings are shown net of all platform costs and are based on efficiency gains observed on comparable plants. This is an estimate built on your inputs, not a guarantee. Actual results depend on plant configuration, load profile, existing sequence quality, and equipment condition. A plant already running a well-tuned optimization sequence has less headroom than one running fixed setpoints from 2009 — and we’ll tell you which one you have before you spend anything.

Start The Conversation

Start With The Data

An assessment uses your actual trend data rather than averages — load profile, staging behavior, approach temperatures, and how your plant responds through a real cooling season. We’ll tell you what the opportunity is, and we’ll tell you if there isn’t one.

The agents make your building run better. The open system makes sure they’re never the thing holding you in place.

Both matter.